uns k02401, mil spec mil-s-23495, afnor 35-501 e24-2, afnor 35-501 e24-3, bs4360 40(a)b, bs4360 40c, csag40-21230 g, din 17100 rst 37-2, din 17100 st37-3u, en10025(90) fe e360b(fn), en10025(90) fe e 360 c, en10025(93) s235jr(g2), en10025(93) s235 j0, is 226, is fe 410-s, jis 3101 ss 400, jis 3106 sm 400a, jis 3106 sm 400b, iso 630 fe 360 b, iso
Carbon Steel IS 2062 GR.B Sheet Plate, IS2062 Mild Steel Other Related Products. Incoloy 800 Flanges; Aluminium Alloys 7050 Sheet Plate; People Also Searched For. is 2062 plate thickness tolerance, carbon steel plate, is 2062 grade b hardness, is 2062 gr b, is 2062 gr.b carbon steel plate specification, mild steel is 2062 grade b, ms is 2062 gr.b sheet plate exporter in india, a36 carbon steel structural steel plate, carbon steel sheet exporter in
Carbon and low alloy steel also known as Mild steel. steels with a low carbon content and without alloy are softer and more easily formed, it is a low-cost material that is easy to shape. While not as hard as higher-carbon steels, carburizing can increase its surface hardness. carbon structural steel has the proper tensile strength, good toughness, plasticity, processing property.
DATOS Y CARACTERÍSTICAS PRINCIPALES - UPCommonsen10025 (93) din17100 (87) une 36080 (90) nf a35-501 (87) bs4360 (90) uni 7070 (84) sis (75) astm (96) jis g3101 (95) s185 1.0035 st 33 a 310-0 a 33 - fe 320 141300-00 - - s235jr 1.0037 st 37-2 ae 235 b e 24-2 40a fe 360 b 141311-00 s235jrg2 1.0038 rst 37-2 ae 235 b fn - 40b - 141312-00
E250 Steel Plate Carbon Steel IS 2062 GR E250 Sheets The IS 2062 E250 Grade A Steel Sheet also has a smooth transition and can be made in different rust proof finishes.There are E250, 350, 410 and 450 standards of plates. The width of the E250 Gr A Steel Plates range from 1000mm to 3000mm and the thickness ranges from 1mm to 300mm.The material is used to produce the IS 2062 E250 Grade B Steels Plate in hot rolled or cold rolled conditions.
EN10025(93) S 335K2G3,S 335K2G4 these steel grade are belongs to Hot rolled products of structural steels in EN10025 standard. For S355 steel, S means structural . 355 mean it's yield strength should be more than 355 MPa.
EN10025(93) S235JR(G2),S235 J0,S235J2G3,S235J2G4 steel Bebon International is a professional EN10025 (93) S235JR (G2),S235 J0,S235J2G3,S235J2G4 steel plate steel exporter and a steel Stockist in china. We keep more than 1000 tons EN10025 (93) S235JR (G2),S235 J0,S235J2G3,S235J2G4 steel plate steel in stock every month.
EN10025(93) S275JR steel, EN10025(93) S275JR low alloy EN10025(93) S275JR low alloy high strength steel also can be called EN10025(93) S275JR common low alloy steel, EN10025(93) S275JR low alloy structural steel. EN10025(93) S275JR low alloy high strength steel's total alloy content usually is not more then 3% . Except for Si and Mn, there is V,Ti,Nb,Al,Cr,Ni,Re,N and so on.
From the name, we can see that, EN10025(93) S355JR steel belongs to German standard (DIN) steel, S says a structural steel, 355 indicates yield strength lower limit value. In real life, EN10025(93) S355JR steel is often produced into hot-rolled coil and hot-rolled slit strip.
Fe 510 D Material, Fe 510 D Steel Pipe, Fe 510 B Uni 7070 EN10025(93) EN10025(90) DIN 17100:NFA 35-501:BS4360:JIS 3106:S355J2G3:Fe510 D1:St 52-3 N-50 D:SM 490C:We offer wide range of Feedwater Heater Tubes, Regenerative Feed Water Heating System & Open Feedwater Heater System at factory price.
Hot rolled products of structural steelsEUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 10025-3 November 2004 ICS 77.140.10; 77.140.50 Supersedes EN 10113-1:1993, EN 10113-2:1993
en10025(93) en10025(90) din 17100 nfa 35-501 bs4360 jis3101; s275j0:fe 430c:st 44-3u:e28-3:43 c
MEsteel - Qualities Equivalence Tables Construction Steel en 10025(93) en 10025 (90) nbna21201. din 17100. nfa35501. mnc 850 e. iso 1052. uni 7070 a 330-1,2 a-360 1,2,3 a-410 1,2,3 e 295. fe 490-2. a 490-1,2. st 50 EN 10025 :1993Notes :1) FU = rimming steel, FN = rimming steel not permitted, FF = fully killed steel, opt = at manufacturers option. 2) It is permissible to exceed the specified values provided that for each increase of 0.001% N the P content is reduced by 0.005%; the N of the ladle analysis shall not however exceed 0.012%. 3) The max value for N does not apply if the analysis shows a minimum total