16MnCr5 (Italy, UNI) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product 16MnCr5 on-line
16MnCr5 Machinable Annealing - M.T. Acciai s.r.l.16MnCr5 (UNI EN 10084) PROPERTIES AND EMPLOYEMENTS IT IS AN EXCELLENT CASE-HARDENING STEEL THAT COMBINES A GOOD TOUGHNESS IN THE NUCLEUS WITH AN ELEVATED HARDNESS OF THE CASE-HARDENED LAYER.
16MnCr5 steel are alloyed case hardening engineering steels for parts which require core tensile strength of 800 1100 N/mm² and good wearing resistance. It is an engineering material typically used to manufacture piston bolts, camshafts, levers and other vehicle and mechanical engineering components.
16MnCr5 Round Bar Suppliers, 1.7131 Gear Steel Round Bar It is an engineering material typically used to manufacture piston bolts, camshafts, levers and other vehicle and mechanical engineering components. 16MnCr5 is an alloyed case hardening steel used for e.g. mechanical engineering components. 16MnCr5 grade is
16MnCr5, 1.7131, 20MnCr5, 1.7147, 21MnCr5, 1.2162Heat treatment and plastic working 16HG, 16MnCr5, 1.7131, 20HG, 20MnCr5, 1.7147 description Steel designed for parts up to 30 mm in diameter subjected to low stresses and abrasion, for example:camshafts, pins, smaller gears, spindles, bushings and gears operating at high speed. Weldable, machinable and cuttable steel.
General Information. 20MnCr5 is a case-hardening steel with low carbon content but good hardenability reaching good wear resistance due to high surface hardness after hardening.
20MnCr5 Steel 20MnCr5 Forging Steel 20MnCrS5 SteelWe can also provide you with 16MnCr5 alloy steels and 16MnCr5/20MnCr5 dual certified steels. This steel is carburising steel used for components requiring high wear resistance surface, coupled with tough cores to resist shock loads and strength to give large service life. The Indian equivalent of this standard can be found in IS9175 (Part 20).
42CrMo4 Alloy Steel, BS EN 10250 Engineering SteelBS EN 42CrMo4 Alloy Steel is a common Chromium-Molybdenum steel. Otai steel supplies prime 42CrMo4 alloy steel which is widely used as engineering steel.
16MnCr5 Standard Number:ITEM Standard Number Descriptions 16MnCr5 Chemical composition(mass fraction)(wt.%) Chemical Min.(%) Max.(%) C Si Mn P S Cr Ni Mo V Ta W N Cu Co Pb B Nb Al Ti Other C Si Mn P S Cr Ni 0.14-0.1 9 0.40 1.00-1.3 0 0.035 0.035 0.80-1.1 0 Mo Al Cu Nb Ti V Ce N Co Pb B Other 16MnCr5 Physical Properties Tensile strength 115-234 b/MPa
Equivalent Grades ALLOY STEEL16MnCr5 - 16MnCr5 17Mn1Cr95 - 5120 15Cr3 523A14 15Cr3 15Cr65 EN206 5015 FILESTEEL - - - - - EN18B 530A40 37Cr4 40Cr1 EN18B 5140 SCM420 708M20 - - - - SAE8620 805M20 - 20NiCrMo2 EN362 SAE8620 CARBON STEEL Internal Standard Equivalent Grades BS DIN IS EN SAE/AISI JIS
Examination of the processability of 16MnCr5 by means of Case hardening steel 16MnCr5 16MnCr5 (1.7131) is a low alloyed steel with case hardening capabilities. It is widely used in drivetrain parts and especially in gears. The chemical composition of the used powder can be seen in Table 1. Table 1.
The evaluation of wear progress of gear tooth flanks made of 16MnCr5 was performed using non-destructive micro-magnetic testing, specifically Barkhausen noise (BN) and incremental permeability (IP). Based on the physical interaction of the microstructure with the magnetic field, the micro-magnetic c 16MnCr5 / 1.7131 - SteelNumber - Chemical composition Properties of steel 16MnCr5 (1.7131) Weldability:It is a MnCr alloy steel, easily hot machinable and weldable Hardenability:It has a low hardenability and therefore it can show good core features till thicknesses of about 20 mm.